Start new topic Forum Latest digest Sign in Create account
Search
CrochetKnittingOther hand-madeChat

​Nice Beads Rose

Susan
Susan
Mar 25, 2020 01:32 AM
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose
​Nice Beads Rose

You'll need:

Beads of any colour you like, and gold and green;
Thin wire;
Thick wire;
Mouline threads or florists' tape.

Instructions

Beading scheme consists of
6 petals;
5 sepals;
5 leaves.

Take a piece of wire of a meter and fold in half. Collect 16 beads. Place them in the middle of the wire, where you make a fold.

Create a loop by twisting it. Dilute the edges in different directions, and hang eight beads on them. Twist the base material again. As a result, five loops should come out.

After you did it, put 16 pieces of material, and with one edge go through the beads 4 loops. Eight more beads and draw wire through the space of the fourth beads of the previous loop. Do the same manipulations with the second end. The next ridge will be directed down. Take 12 pieces of material, and push the end through the fourth of the low loops. Such a procedure must be woven three times, and in the fifth, string 14 beads, and pass the wire through the eighth beads into a near loop.

Then, continue working from top to bottom. Take eight beads, pull the end of the wire through the seventh of the future loop. Twelve more beads and the wire edge are drawn through 5 beads of the neighboring loop. Do such actions with the other half, until the petal ends.

Proceed to work on the border of the petal. Rewind the wire with a length of 40 cm and put it into one thing in the center of the petal at the top of the loop. On the first edge, cast on six beads. Weaving does not change its pattern. The hue of the edging should be distinctive from the petal. Then its relief will be more noticeable.

The first part is ready. Turn to the creation of sepals. To weave them, collect emerald beads on the main material, at the end leave one and bend. Two things move to the primary.

Attach a piece of wire under the beads. String eight beads, and add 12 beads at the edges. Twist everything. The scheme of the next stage of weaving is as follows, on the basis we put on 12 beads, on the rest - 14. After all this, spin the three pieces of wire and get the figure "eight". In the thinnest place, tie another wire with beads. On each half of the weave, there will be 21 beads. On the main part, we string 25 beads and put it into a bead of an arch standing next to it. In the end, twist everything together.

After 6 petals and 5 sepals are ready, begin to collect in a step-by-step way. Roll up the petal, it will be the core. Attach it to the leg. Also attach the next one and wrap the first one. Wind florists tape on them and fix it. Wrap further petals with tape and bend them a little. The sepals will be at the top.

Weave the leaves in the French way and wind the tape to the stem.
Like!3
874
No comments